Test yourself on Electrical Power & Energy with exam style questions, marked instantly.
Flashcards that come back just before you would forget them.
A revision plan that remembers what you know and shows what to do next.
See which topics you have nailed and which need another look.
Quiz yourself on Electrical Power & EnergyGet your flashcardsBuild my revision planTrack my progress⚡ The Expensive Shower
📚 Three Power Equations — When to Use Each
P = IV — Use when you know current AND voltage
P = I²R — Use when you know current AND resistance (no voltage given)
P = V²/R — Use when you know voltage AND resistance (no current given)
How these all connect (combining P = IV with V = IR):
- P = IV, substitute V = IR → P = I × (IR) = I²R
- P = IV, substitute I = V/R → P = (V/R) × V = V²/R
⚡ Kilowatt-Hours (kWh) — The Billing Unit
What it is: The energy used by a 1 kW appliance running for 1 hour.
Why we use it: Joules are too small for household bills. 1 kWh = 3,600,000 J!
Example calculation:
- 3 kW kettle used for 5 minutes = 3 × (5/60) = 3 × 0.083 = 0.25 kWh
- At 30p per kWh: Cost = 0.25 × 30 = 7.5p
📊 Electrical Power Formulas

Figure 1: Two of the power equations as triangles: P = I × V and P = I² × R. P = V² ÷ R follows by substitution.
📊 Power Ratings of Common Appliances
| Appliance | Power | Energy in 1 hour | Cost at 30p/kWh |
|---|---|---|---|
| Phone charger | 5 W | 0.005 kWh | 0.15p |
| LED bulb | 10 W | 0.01 kWh | 0.3p |
| Laptop | 50 W | 0.05 kWh | 1.5p |
| Television | 100 W | 0.1 kWh | 3p |
| Fridge (average) | 150 W | 0.15 kWh | 4.5p |
| Desktop computer | 200 W | 0.2 kWh | 6p |
| Washing machine | 2000 W | 2 kWh | 60p |
| Kettle | 3000 W | 3 kWh | 90p |
| Electric shower | 9000 W | 9 kWh | £2.70 |
Key insight: A 10-minute shower costs more than leaving a phone charger plugged in for an ENTIRE WEEK!
⚙️ How It Works: Why High-Current Appliances Cost More
Power in an electrical circuit represents the rate of energy transfer — how many joules of electrical energy are converted into other forms (heat, light, sound, kinetic) every second.
The equation P = I²R reveals something important: power increases with the square of the current. Doubling the current quadruples the power dissipated as heat in a resistor. This is why:
- High-current appliances (showers, kettles) are very expensive to run
- National Grid transmits electricity at very high voltage and low current to minimise energy losses in cables (P = I²R — lower I = far less heating loss)
- Fuses are rated by current — too much current means dangerous overheating
The equation P = V²/R shows that at a fixed voltage (like mains 230 V), lower resistance means more power. This is why a kettle (low resistance heating element) is much more powerful than an LED bulb (high resistance).
Quick Check: A toaster operates at 230 V with a current of 4 A. Calculate its power rating.
P = I × V = 4 × 230 = 920 W.
📖 Key Definitions
Power (P): The rate of energy transfer — the energy transferred per second. Measured in watts (W). 1 W = 1 J/s.
Watt (W): The SI unit of power. 1 watt = 1 joule of energy transferred per second.
Kilowatt (kW): 1000 watts. Used for high-power appliances.
Kilowatt-hour (kWh): The unit of energy used on electricity bills. Energy used by a 1 kW appliance running for 1 hour. 1 kWh = 3,600,000 J.
Energy transferred (E): Total energy transferred by an appliance. E = P × t. Measured in joules (J) or kWh.
📋 Key Facts Summary
- Power equations: P = IV, P = I²R, P = V²/R
- Energy equation: E = Pt or E = IVt
- Billing equation: Energy (kWh) = Power (kW) × time (hours)
- Cost: Cost = Energy (kWh) × price per unit
- Power unit: watts (W)
- 1 kW = 1000 W
- 1 kWh = 3,600,000 J = 3.6 × 10⁶ J
- Higher power + longer time = more energy used = higher bill
⚖️ Which Power Equation to Use?
| Equation | Use when you know... | Finding... |
|---|---|---|
| P = IV | Current (I) and Voltage (V) | Power |
| P = I²R | Current (I) and Resistance (R) | Power (no V given) |
| P = V²/R | Voltage (V) and Resistance (R) | Power (no I given) |
| E = Pt | Power (P) and time (t in seconds) | Energy in joules |
| E = P × t | Power (kW) and time (hours) | Energy in kWh |
Quick Check: A 2 kW electric fire is used for 3 hours. The electricity unit price is 25p per kWh. What is the cost?
Energy = 2 kW × 3 hours = 6 kWh. Cost = 6 × 25p = 150p = £1.50.
⚠️ Common Misconceptions
Misconception 1: "Watts and joules are the same thing"
Watts and joules measure different things. A joule is a unit of energy (a fixed amount of energy). A watt is a unit of power — the rate of energy transfer (joules per second). An appliance rated at 100 W transfers 100 joules every second. The longer it runs, the more total energy (joules) it uses.
Misconception 2: "Multiplying kilowatts by seconds gives kWh"
This is a very common unit error. The kWh formula requires kilowatts × hours, not kilowatts × seconds. If you're given time in seconds, either convert to hours or use E = Pt (where E is in joules, P is in watts, t is in seconds). Mixing these up will give an answer that's 3600 times too big or too small.
Misconception 3: "High voltage appliances use more energy"
Energy use depends on both voltage and current (P = IV) and on time (E = Pt). A high-voltage appliance drawing very little current may use less power than a low-voltage device drawing lots of current. It's the power rating multiplied by time used that determines the cost — not voltage alone.
🧠 Memory Aid
Three power equations from one — "PIV is like PIE":
Start with P = IV (the PIE). To get P = I²R: replace V with IR (from Ohm's Law). To get P = V²/R: replace I with V/R. You only need to remember P = IV and V = IR, then derive the others.
kWh billing — "kW × Hours = kWh":
Kilowatts × Hours = Kilowatt-Hours. The unit tells you exactly what to multiply. If given watts, divide by 1000 first. If given time in minutes, divide by 60 first.
Which equation? — "Got V and I? Use P = VI. Got I and R? Use I²R. Got V and R? Use V²/R":
Match the letters in the equation to the letters of the quantities you've been given in the question.
🎓 Higher Tier Only: Power Loss in Transmission
The National Grid transmits electricity over long distances. Power is lost as heat in the cables because cables have resistance. The power lost is given by:
To minimise loss, the current must be kept as small as possible. Since P = IV, for a given power output, a smaller current requires a higher voltage. This is why the National Grid transmits at up to 400,000 V — it reduces current, which dramatically reduces the I²R heating loss. Transformers are used to step voltage up at the power station and step it back down to 230 V for safe domestic use.
🎯 Exam Focus
Exam Favourite
This topic is on all four boards (AQA, Edexcel, OCR A and OCR B). The question types below are worth practising.
Examined in Edexcel 1PH0/2 (Paper 2). Context-based: household appliance energy cost calculations are a staple question type. Edexcel emphasises energy cost using E = Pt and unit price. Expect calculation questions, unit conversions, and "explain" questions about energy efficiency.
What examiners love to ask:
- Calculate power using P = IV, P = I²R, or P = V²/R
- Calculate energy transferred using E = Pt
- Calculate running cost using E = P(kW) × t(hours) × price
- Explain why the National Grid uses high voltage (Higher tier)
- Compare running costs of two appliances
- Choose the correct power equation given different known quantities
💡 Exam Tips for Electrical Power and Energy
🎯 Common Question Types:
- Calculate power from V and I (2 marks)
- Calculate energy in joules from P and t in seconds (2 marks)
- Calculate energy in kWh and cost (3 marks)
- Choose and apply correct power equation (2–3 marks)
- Explain why National Grid uses high voltage (3 marks — Higher)
📝 Key Command Words:
- Calculate — show equation, substitution, and units
- Explain — state the equation and say what happens to each variable
- Compare — state which uses more energy and why
- Evaluate — consider pros and cons of a claim
⚠️ Common Mistakes to Avoid:
- Using kW × seconds instead of kW × hours for kWh
- Forgetting to divide watts by 1000 to get kilowatts
- Using the wrong power equation (check what quantities you're given)
- Forgetting to state units: W, J, kWh
- Confusing energy (J or kWh) with power (W or kW)
Quick Check: A component has a resistance of 10 Ω and carries 3 A of current. Calculate the power dissipated.
Use P = I²R = 3² × 10 = 9 × 10 = 90 W.
Make this stick
Signing in gives access to all PrepWise features.