Specific Latent Heat

Test yourself on Specific Latent Heat with exam style questions, marked instantly.

Flashcards that come back just before you would forget them.

A revision plan that remembers what you know and shows what to do next.

See which topics you have nailed and which need another look.

Quiz yourself on Specific Latent HeatGet your flashcardsBuild my revision planTrack my progress

📖 Why Steam Burns Worse Than Boiling Water

Here's a painful truth: getting scalded by steam at 100°C causes FAR worse burns than boiling water at 100°C. Same temperature — so why the difference? Because steam carries "hidden" energy — the energy that was needed to turn water into steam. When steam touches your skin and condenses back to water, all that hidden energy DUMPS into you. The word "latent" literally means "hidden" — it's energy stored in the state change itself, invisible to thermometers!
Specific Latent Heat Equation (ON FORMULA SHEET)
E = m × L
Energy (J) = mass (kg) × specific latent heat (J/kg)

🔬 Understanding Specific Latent Heat

Specific latent heat (L) is the energy needed to change the state of 1 kg of a substance WITHOUT changing its temperature. The word "specific" means "per kilogram."

Why does it take so much energy? Because energy must break the bonds between particles — not make them move faster. During the state change, ALL the energy goes into bond-breaking (potential energy), which is why temperature stays constant.

The bigger the latent heat value, the stronger the bonds between particles and the more energy needed to pull them apart.

📊 Heating Curve — Temperature vs Time

A heating curve sketch: temperature in degrees Celsius against time. The line rises, then goes flat at 0 °C (1: melting, solid and liquid, latent heat of fusion), rises more gently to 100 °C, then goes flat at 100 °C for longer (2: boiling, liquid and gas, latent heat of vaporisation) before rising again. It is a sketch, not to scale.

Figure 1: Heating curve for water. The heater supplies energy at a constant rate. The flat sections show where latent heat is absorbed at constant temperature: melting at 0 °C (1) and boiling at 100 °C (2). The boiling section is longer because boiling needs more energy than melting.

Sketch: not to scale.

KEY INSIGHT: During state changes, temperature stays constant because energy goes into breaking bonds (latent heat), not increasing particle speed.

📚 Two Types of Latent Heat

Specific Latent Heat of FUSION (Lf):

  • Energy to change between solid ↔ liquid (melting/freezing)
  • For water: Lf = 334,000 J/kg
  • "Fusion" = fusing/joining (particles come together when freezing)

Specific Latent Heat of VAPORISATION (Lv):

  • Energy to change between liquid ↔ gas (boiling/condensing)
  • For water: Lv = 2,260,000 J/kg
  • MUCH bigger than fusion — particles must completely separate

Why Lv is much greater than Lf: Going solid → liquid only loosens bonds. Going liquid → gas completely breaks them. More bond-breaking = more energy needed.

Quick Check: Calculate the energy needed to melt 2 kg of ice at 0°C. (Lf of water = 334,000 J/kg)

⚙️ Why Latent Heat of Vaporisation is So Much Larger

When a solid melts, particles only need to break free from their fixed positions — they remain close together in the liquid. The forces are weakened but not fully overcome.

When a liquid boils, particles must completely escape all attractive forces and spread to very large distances. This requires overcoming essentially ALL the intermolecular forces. That's why the latent heat of vaporisation of water (2,260,000 J/kg) is nearly 7 times greater than the latent heat of fusion (334,000 J/kg).

Real-world consequence: This is why sweating cools you so effectively — evaporation requires a very large amount of energy, which is taken from your skin, cooling it rapidly. Similarly, steam burns are more severe than boiling water burns because steam releases its large latent heat of vaporisation when it condenses on your skin.

📖 Key Definitions

Specific latent heat (L): The energy required to change the state of 1 kg of a substance without changing its temperature. Units: J/kg.

Specific latent heat of fusion (Lf): Energy per kg needed to melt a solid (or freeze a liquid). For water: 334,000 J/kg.

Specific latent heat of vaporisation (Lv): Energy per kg needed to boil a liquid (or condense a gas). For water: 2,260,000 J/kg.

Latent: From Latin meaning "hidden" — it is "hidden" because it changes the state of the substance without changing its temperature, so a thermometer cannot detect it.

Specific heat capacity (c): Energy per kg per degree to change temperature WITHIN a state (contrasted with latent heat which is for state changes at constant temperature).

⚠️ Common Misconceptions

Misconception 1: "Latent heat changes the temperature"

No — latent heat is the energy transferred during a state change, and during this process temperature stays CONSTANT. If temperature is changing, specific heat capacity (E = mcΔT) applies, not specific latent heat. They describe different processes.

Misconception 2: "Latent heat of fusion is bigger than latent heat of vaporisation"

The opposite is true. Vaporisation requires far more energy than melting because all intermolecular bonds must be fully broken (not just loosened). For water, Lv (2,260,000 J/kg) is about 7× larger than Lf (334,000 J/kg).

Misconception 3: "Specific latent heat depends on the amount of substance"

No — "specific" means per kilogram. The specific latent heat (L) is a fixed property of the material. To find the total energy (E), you multiply by the mass: E = mL. A bigger mass needs more total energy, but L itself doesn't change.

Quick Check: Explain why the specific latent heat of vaporisation of water is much greater than its specific latent heat of fusion.

🧠 Memory Aid

Remembering the two types:

  • Fusion = Freezing/melting (solid-liquid boundary) — think "F for Floor" (the lower level)
  • Vaporisation = Very hot (liquid-gas boundary) — think "V for Very high energy"

The equation E = mL: Think "Enormous mass x Latent heat = Enormous energy." Or use the triangle: E on top, m bottom-left, L bottom-right. Cover what you want to find.

Why steam burns more: Steam at 100°C → skin → condenses → releases 2,260,000 J/kg (latent heat) PLUS cools down further. Boiling water only cools down — no latent heat released. So steam is the nastier one.

🎓 Higher Tier: Calculating Latent Heat from Experimental Data

In an experiment to find specific latent heat of fusion of ice, you might:

  1. Use a known mass of ice at 0°C in an insulated container
  2. Supply a known electrical power (P = IV) for a measured time
  3. Energy supplied: E = P × t (in Joules)
  4. All this energy goes into melting the ice (temperature stays at 0°C)
  5. Calculate: L = E / m

Sources of error: Heat loss to surroundings (use insulation), not all ice melting. To correct, run a "blank" experiment with no heater to measure melting from room-temperature heat alone.

Cooling curves: You can also determine L from cooling — the flat section on a cooling curve is where energy is released as a liquid freezes. Time × power = E = mL gives you L.

🎯 Exam Focus

Frequently Examined

Specific latent heat is a calculation topic on all four boards (AQA, Edexcel, OCR A and OCR B). Be ready to apply E = mL to unfamiliar contexts and to choose between the latent heat of fusion (Lf) and of vaporisation (Lv).

Edexcel (1PH0/2, Paper 2) uses context-based questions around material properties and industrial processes, such as refrigeration cycles, cooking and industrial drying. The latent heat value may be given in the question, or you may have to choose between Lf and Lv for the scenario.

  • Calculation: E = mL (2-3 marks): Given mass and L, find energy. Or rearrange to find mass. Always show working and include units (J).
  • Explain why Lv > Lf (3 marks): Link to bond-breaking — melting loosens bonds (particles stay close), boiling completely breaks all bonds (particles separate fully).
  • Explain why temperature stays constant (3 marks): Energy → breaking bonds → potential energy increases, kinetic energy unchanged → temperature unchanged.
  • Steam vs boiling water context question (2 marks): Steam releases latent heat of vaporisation when it condenses, giving more total energy transfer to skin.
  • "Suggest" questions (Edexcel): Given an unusual state change scenario, suggest which latent heat value applies (fusion vs vaporisation) and calculate the energy involved.

💡 Exam Tips for Specific Latent Heat

🎯 Common Question Types:

  • Calculate energy needed to change state using E = mL (2-3 marks)
  • Explain why temperature stays constant during state change (3 marks)
  • Explain why Lv is greater than Lf (3 marks)
  • Interpret heating/cooling curve with latent heat sections (2-3 marks)

📝 Key Command Words:

  • Calculate: Use E = mL, show each step, give correct units (J)
  • Explain: Must link energy → bonds → kinetic/potential energy → temperature
  • Compare: State values and explain the difference in terms of bond-breaking
  • Suggest: May ask why steam is more dangerous than boiling water

⚠️ Common Mistakes to Avoid:

  • Confusing E = mcΔT (temperature change) with E = mL (state change) — different equations for different situations
  • Saying latent heat increases temperature — it does NOT; temperature stays constant
  • Forgetting units — L is in J/kg, E is in J, m is in kg
  • Saying Lf > Lv — vaporisation always needs more energy than fusion

Quick Check: How much energy is released when 0.5 kg of steam condenses to water at 100°C? (Lv = 2,260,000 J/kg)

Make this stick

Signing in gives access to all PrepWise features.

PrepWise is a trading name of A3M Quality Solutions Limited, registered in England and Wales, company number 14959172. Registered office: 202 Stroud Road, Gloucester, GL1 5LA. ICO registration ZC267069.