Resistance & Ohm's Law

Test yourself on Resistance & Ohm's Law with exam style questions, marked instantly.

Flashcards that come back just before you would forget them.

A revision plan that remembers what you know and shows what to do next.

See which topics you have nailed and which need another look.

Quiz yourself on Resistance & Ohm's LawGet your flashcardsBuild my revision planTrack my progress

🔌 The Narrow Pipe Problem

Imagine trying to push water through different pipes. A wide, smooth pipe offers little resistance — water flows easily. A narrow, rough pipe resists the flow — you need more pressure to push the same amount through. Electrical resistance works the same way. A thick copper wire has low resistance; a thin nichrome wire has high resistance. The equation V = IR tells you that for a given voltage, higher resistance means less current can flow.

📚 Understanding Resistance and Ohm's Law

Ohm's Law states that the voltage across a component is directly proportional to the current through it, provided temperature stays constant: V = I × R (Voltage in volts = Current in amps × Resistance in ohms). Rearranged: R = V ÷ I (to find resistance) and I = V ÷ R (to find current). A component is ohmic if it obeys this law at constant temperature (e.g. a resistor). A component is non-ohmic if resistance changes with conditions (e.g. a filament bulb — resistance increases with temperature; a diode — only conducts in one direction).

Ohm's Law
V = I × R
Voltage (V) = Current (A) × Resistance (Ω)

Resistance is a measure of how much a component opposes the flow of current.

Unit: Ohms (Ω) — named after Georg Ohm

  • Higher resistance → lower current (for same voltage)
  • Higher voltage → higher current (for same resistance)
  • R = V / I (the most useful rearrangement)

📊 The V-I-R Triangle

A triangle split into three parts. V, for potential difference, is in the top part. I, for current, and R, for resistance, sit side by side in the bottom part with a multiplication sign between them.

Figure 1: The V-I-R triangle. Cover the quantity you want to find and read off the calculation. V is in volts, I in amperes and R in ohms.

🔧 What Affects the Resistance of a Wire?

Four factors:

  • Length — longer wire = more resistance (R ∝ L)
  • Cross-sectional area — thicker wire = less resistance (R ∝ 1/A)
  • Material — different materials have different resistivities
  • Temperature — for metals, hotter = more resistance

Why length increases resistance:

  • Electrons must travel further through the material
  • More collisions with metal ions along the way
  • More opposition to flow overall

Why thickness decreases resistance:

  • More pathways for electrons to flow side-by-side
  • Like a wider road with more lanes — less congestion
  • Less crowded = easier flow

⚡ Ohmic vs Non-Ohmic Conductors

Ohmic conductors: Resistance stays CONSTANT

  • Examples: Fixed resistors, metal wires (at constant temperature)
  • V-I graph is a straight line through the origin
  • Obey Ohm's Law: V = IR with constant R

Non-ohmic components: Resistance CHANGES

  • Filament lamp — R increases as it heats up (curved V-I graph)
  • Diode — very high R in one direction, low R in the other (only allows current one way)
  • Thermistor — R decreases as temperature increases
  • LDR (light-dependent resistor) — R decreases as light intensity increases

⚙️ How It Works: Why Resistance Increases with Temperature (Metals)

At higher temperatures, the metal ions in the wire vibrate more vigorously. This increases the chance that a free electron will collide with an ion as it moves through the wire.

Each collision slows the electron down, transferring some of its kinetic energy to the ion as thermal energy (heat). More collisions = more opposition to flow = higher resistance.

This is why a filament lamp has a non-linear V-I graph: as more current flows, the filament heats up, its resistance increases, which limits further current increases. The graph curves upward (V increases faster than I).

For a thermistor, the opposite happens: it's made of semiconductor material where higher temperature frees more charge carriers, so resistance decreases as temperature rises. This makes thermistors useful as temperature sensors in thermostats and fire alarms.

🧪 Required Practical: Resistance of a Wire

Equipment: Power supply, ammeter, voltmeter, metre ruler, resistance wire, crocodile clips

Method:

  1. Set up circuit with ammeter in series, voltmeter in parallel across wire
  2. Use crocodile clips at measured lengths (e.g., 10, 20, 30, 40, 50 cm)
  3. For each length: record V and I
  4. Calculate R = V / I for each length
  5. Turn off power between readings (prevent heating affecting results)
  6. Plot R (y-axis) against length (x-axis)

Expected result: Straight line through origin — R is directly proportional to length

Control variables: Same wire material, same cross-sectional area, constant temperature

Quick Check: A resistor has 12 V across it and 0.5 A flows through it. What is its resistance?

📖 Key Definitions

Resistance (R): A measure of how much a component opposes the flow of electric current. Measured in ohms (Ω). Formula: R = V/I.

Ohm (Ω): The SI unit of resistance. 1 Ω = 1 V/A (one volt per amp).

Ohm's Law: The potential difference across a conductor is directly proportional to the current through it, provided temperature remains constant. V = IR.

Ohmic conductor: A component whose resistance stays constant regardless of current (e.g., fixed resistor at constant temperature). Gives a straight-line V-I graph through the origin.

Thermistor: A component whose resistance decreases as temperature increases. Used as a temperature sensor.

LDR (Light-Dependent Resistor): A component whose resistance decreases as light intensity increases. Used as a light sensor.

📋 Key Facts Summary

  • Ohm's Law: V = IR
  • Resistance unit: ohms (Ω)
  • Longer wire → more resistance
  • Thicker wire → less resistance
  • Hotter metal → more resistance (more ionic vibration)
  • Hotter thermistor → less resistance
  • Brighter LDR → less resistance
  • Filament lamp: resistance increases as it heats up → curved V-I graph
  • Diode: allows current in ONE direction only

⚖️ Ohmic vs Non-Ohmic: V-I Graphs

ComponentV-I Graph ShapeResistance Behaviour
Fixed resistorStraight line through originConstant
Filament lampS-shaped curve (steeper at high V)Increases with temperature
DiodeFlat near zero then steep riseVery high (reverse), very low (forward)
ThermistorDepends on temperature conditionsDecreases as temperature rises

Quick Check: Why does a filament lamp have a curved V-I graph rather than a straight line?

⚠️ Common Misconceptions

Misconception 1: "All components obey Ohm's Law"

Only ohmic conductors (like fixed resistors at constant temperature) obey Ohm's Law. Components like filament lamps, diodes, thermistors, and LDRs are non-ohmic — their resistance changes with conditions. Ohm's Law states that V ∝ I only when resistance is constant.

Misconception 2: "A thicker wire always has more resistance"

This is the opposite of the truth. A thicker wire has a larger cross-sectional area, which means more pathways for electrons to travel side-by-side. This reduces resistance. Think of a wider road allowing more traffic — it decreases congestion (resistance), not increases it.

Misconception 3: "Resistance of a metal decreases when it gets hotter"

For metals, the opposite is true: resistance increases with temperature (greater ionic vibration causes more electron collisions). It is thermistors and semiconductors that show decreasing resistance with increasing temperature. Students often confuse these two opposite behaviours.

🧠 Memory Aid

VIR Triangle — "Very Important Relationship":

Write V at the top, I and R at the bottom. Cover the letter you want to find: V on top alone = I × R; I on bottom-left = V ÷ R; R on bottom-right = V ÷ I.

Non-ohmic components — "FDT Changes":

Filament lamp, Diode, Thermistor — these three all have changing resistance. Everything else (fixed resistors) is ohmic.

Thermistor vs LDR — "Hot is Less, Bright is Less":

Hotter thermistor = less resistance. Brighter LDR = less resistance. Both sensors work the same way — the thing they detect reduces their resistance.

Wire resistance factors — "LAMT":

Length (more = more R), Area (more = less R), Material, Temperature.

🎓 Higher Tier Only: Resistivity

The resistance of a wire depends on its resistivity (ρ) — a property of the material itself, measured in Ω·m.

R = ρL / A
Resistance (Ω) = resistivity (Ω·m) × length (m) ÷ cross-sectional area (m²)

This equation shows that resistance is directly proportional to length and inversely proportional to cross-sectional area — it quantifies what the GCSE required practical investigates qualitatively. Copper has very low resistivity (~1.7 × 10⁻⁸ Ω·m), which is why it's used for electrical wiring.

🎯 Exam Focus

Exam Favourite

This topic is on all four boards (AQA, Edexcel, OCR A and OCR B). The question types below are worth practising.

Examined in Edexcel 1PH0/2 (Paper 2). CP5 (Investigating electrical circuits, including the V-I-R relationship for a resistor and a filament lamp) is a Core Practical tested directly. Expect method, variable and analysis questions. "Suggest" questions appear for novel component behaviour. V-I graphs are a classic "describe and explain" question type.

What examiners love to ask:

  • Calculate resistance, voltage or current using V = IR
  • Describe and explain the V-I graph for a filament lamp
  • Compare V-I graphs of ohmic and non-ohmic components
  • Explain how resistance of a metal changes with temperature
  • Describe how resistance of a thermistor changes with temperature
  • State one use of a thermistor or LDR
  • Explain the required practical method for resistance of a wire

💡 Exam Tips for Resistance and Ohm's Law

🎯 Common Question Types:

  • Ohm's Law calculation: V = IR or R = V/I (2 marks)
  • Describe V-I graph shape for filament lamp (2 marks)
  • Explain why resistance changes with temperature (3 marks)
  • Required practical: method and control variables (4 marks)
  • State and explain how a thermistor/LDR works (2 marks)

📝 Key Command Words:

  • Calculate — show V = IR substitution with units
  • Describe — say what the graph looks like (shape, gradient)
  • Explain — say why (use "because" with ion vibration)
  • Sketch — draw a labelled graph (axes, origin, shape)

⚠️ Common Mistakes to Avoid:

  • Forgetting units for resistance (Ω, not R)
  • Saying metal resistance decreases with temperature — it increases
  • Confusing thermistor (less R when hot) with metal wires (more R when hot)
  • Drawing filament lamp V-I graph as a straight line — it curves
  • Not turning off the power supply between readings in required practical

Quick Check: A thermistor is placed in ice water, then hot water. What happens to its resistance, and how does this affect current in the circuit?

Make this stick

Signing in gives access to all PrepWise features.

PrepWise is a trading name of A3M Quality Solutions Limited, registered in England and Wales, company number 14959172. Registered office: 202 Stroud Road, Gloucester, GL1 5LA. ICO registration ZC267069.